Cost behaviour and relevant range
Content revised on 3 October 2026. Any completion marker earned before this revision refers to the earlier content version and does not confirm completion of this revised lesson.
Learning goals
- Model total and average cost with stated units and range.
- Identify step changes and distinguish volume effects from efficiency.
Assumptions and scope
- One-month forecasts, no inventory valuation and no tax.
- Linear behavior applies only inside each exercise’s stated range.
- Output measures comparable units and ignores scrap.
Content revised on 3 October 2026. Any completion marker earned before this revision refers to the earlier content version and does not confirm completion of this revised lesson.
A cost-behavior statement needs a driver, a time period and a range of activity. Without those, saying that a cost is fixed or variable is incomplete. This lesson uses units produced as the driver and one month as the period. Within a specified operating range, a variable cost has a constant cost per unit, so its total changes proportionately with units. A fixed cost has a constant total over that same range, so its cost per unit changes when the denominator changes.
Write a simple mixed-cost model as total cost = fixed amount + variable rate × activity. The fixed amount is measured in MU per month; the rate is MU per unit; activity is units per month. Checking these units is an effective way to catch incorrect multiplication. The result is a monthly cost, not a quotation for selling one more unit. That distinction matters because a modeled average contains a share of capacity costs that may not change immediately.
A relevant range describes where the model is a reasonable approximation. A single rented machine may support the forecast activity but not an unlimited number of units. Crossing its practical capacity could require another rental, overtime or a different process. The old fixed amount or variable rate may then cease to apply. It is better to state that the model needs revision than to extend a straight line into a region with no supporting operating evidence.
Some resources change in steps. A team leader may cover a band of workers; another team leader is needed after a threshold. The monthly total is constant inside each band but jumps between bands. A step cost can look fixed in a narrow range and variable across a much wider range. The observation is not contradictory: the question being asked has changed. Always disclose the band before using the amount in a cost forecast.
When comparing two months, separate a change in activity from a change in prices, work methods or capacity. A higher total cost is not automatically poorer control if more useful output was produced. Equally, a falling average unit cost can result entirely from spreading unchanged fixed costs over more output. It does not prove improved material use. A useful explanation identifies which component moved and asks whether the original conditions still hold.
Prepare a small sensitivity table before trusting a forecast. Use a low, central and high activity level inside the stated range; calculate variable cost, fixed cost, total cost and average cost independently. The fixed column should stay level and the variable cost per unit should stay constant. If they do not, either the arithmetic is wrong or the model is different from the one described. Treat the model as a transparent planning tool, not a law of nature or a guarantee about actual expenditure.
Concept verification: [OpenStax, cost behavior](https://openstax.org/books/principles-managerial-accounting/pages/2-2-identify-and-apply-basic-cost-behavior-patterns): fixed and variable describe response to an activity driver within stated conditions; verified 3 October 2026. Original explanations and exercises below are not adapted publisher material.
Worked example: Worked example: A bounded monthly model
A finishing cell has fixed support of 1,200 MU/month plus 3 MU per finished unit, valid from 200 to 800 units/month. Calculate total and average cost at 400 and 600 units.
Solution
At 400 units: variable cost = 1,200 MU; total = 2,400 MU; average = 6 MU/unit. At 600 units: variable cost = 1,800 MU; total = 3,000 MU; average = 5 MU/unit. The extra 200 units add 600 MU. The lower average comes from fixed-cost spreading, with no change in the variable rate.
Read by row; each named column is a text label. Monetary figures are fictional MU. This table is also available as plain text.
| Units/month | Variable MU | Fixed MU | Total MU | Average MU/unit |
|---|---|---|---|---|
| 400 | 1200 | 1200 | 2400 | 6 |
| 600 | 1800 | 1200 | 3000 | 5 |
Independent practice
-
A monthly model is 900 MU + 4 MU/unit, valid for 100–500 units. Calculate total and average at 300 units.
-
A rented work cell costs 700 MU/month and supports up to 500 units. A second identical cell is required above 500 and up to 1,000 units. Variable cost is 2 MU/unit. Find total at 650 units.
-
Within an unchanged 100–600 unit range, monthly fixed cost is 800 MU and variable cost is 5 MU/unit. What extra cost does production rising from 250 to 330 units imply?
Practice answers and reasoning
-
2,100 MU total and 7 MU/unit.
Variable cost is 1,200 MU; adding the fixed 900 MU gives the total. Divide by 300 only for the average.
-
2,700 MU.
Two cells cost 1,400 MU; variable cost is 1,300 MU. The one-cell fixed amount cannot be extrapolated.
-
400 MU.
Only 80 additional units × 5 MU/unit changes; the fixed amount is unchanged.
Common errors to avoid
- Multiplying a fixed cost per unit as though it were a variable rate.
- Forecasting beyond the stated capacity range.
Exit check
-
Can the 200–800 unit example predict 1,200 units reliably?
-
Does a declining fixed cost per unit mean total fixed cost fell?
Exit-check answers
-
No.
Capacity and rate assumptions must be checked outside the stated relevant range.
-
No.
A larger denominator can lower the average with unchanged total cost.